ECOTHERM Electric Hot Water Boiler
Skid-mounted electric boilers that make hot water from electricity alone. For sites with no gas, and for power to heat systems that turn surplus renewable power into heat.
At a glance: The ECOTHERM Electric Hot Water Boiler makes hot water from electricity using individually replaceable heating elements, with 14 standard models from 72 kW to 2,016 kW and custom or cascade units up to 30 MW. It comes pre-wired and skid mounted, runs at 6, 10, or 16 bar, and suits sites with no gas supply and power to heat systems. Hurll Nu-Way supplies, commissions, and services ECOTHERM boilers in Australia.
Hot water from electricity, delivered ready to connect
ECOTHERM electric hot water boilers suit sites where electricity is the only energy source, or where a chimney and gas supply are not practical. They also suit power to heat plants, which turn surplus electricity from solar or wind into stored heat.
Heat comes from screwed-in heating elements, each replaceable on its own, or from an electric flange heater. Every boiler is pre-wired, set up, and tested at the factory, then delivered on a structural steel skid, so site work is mostly connecting water and power.
Smaller models use a 3-stage controller. Larger models use a programmable microprocessor controller with a touch screen and data links to building management systems (BMS). Vertical and horizontal versions are available, and ECOTHERM builds to order in size, voltage, output, and controls. ECOTHERM builds its boilers at its own plant in Austria, to the European Pressure Equipment Directive 2014/68/EU or ASME Section VIII Division 1.
Key advantages
- No gas supply or chimney needed
- Individually replaceable heating elements
- Pre-wired, tested, and skid mounted
- Mild steel or stainless steel shell
- Touch screen control with BMS links
- Built to order up to 30 MW
ECOTHERM Electric Hot Water Boiler specifications
- Output 72 to 2,016 kW standard, up to 30 MW custom
- Operating pressure 6, 10, or 16 bar(g) standard
- Water temperature Up to 110°C standard, higher on request
- Supply voltage 3-phase 415 V standard, up to 690 V for larger units
- Shell material Mild steel P235GH, or stainless steel 304, 316 Ti, or duplex
- Flanges DIN EN 1092-1, PN6, PN16, or PN40
- Design code PED 2014/68/EU or ASME VIII Div. 1
Models and variants
| Model | Output (kW) | Heating elements | Water flow at 20 K (m³/h) | Inlet and outlet |
|---|---|---|---|---|
| EEII-TS-75-VA | 72 | 4 | 3.09 | DN32 |
| EEII-TS-100-VA | 108 | 6 | 4.64 | DN32 |
| EEII-TS-160-VA | 162 | 9 | 6.97 | DN40 |
| EEII-TS-250-VA | 252 | 14 | 10.83 | DN50 |
| EEII-TS-300-VA | 306 | 17 | 13.16 | DN65 |
| EEII-TS-400-VA | 396 | 22 | 17.03 | DN65 |
| EEII-TS-500-HA | 504 | 28 | 21.67 | DN80 |
| EEII-TS-660-HA | 666 | 37 | 28.63 | DN80 |
| EEII-TS-800-HA | 792 | 44 | 34.05 | DN100 |
| EEII-TS-1000-HA | 1,008 | 2 x 28 | 42.99 | DN100 |
| EEII-TS-1200-HA | 1,188 | 2 x 33 | 51.07 | DN125 |
| EEII-TS-1500-HA | 1,512 | 2 x 42 | 65.00 | DN125 |
| EEII-TS-1750-HA | 1,764 | 2 x 49 | 75.23 | DN150 |
| EEII-TS-2000-HA | 2,016 | 2 x 56 | 85.98 | DN150 |
Standard models from ECOTHERM's 8a Electric Boilers brochure. Cascades of two or three boilers reach 3 to 6 MW, and larger units are built to order up to 30 MW.
ECOTHERM Electric Hot Water Boiler brochures and manuals
ECOTHERM's current brochures and the operating and maintenance manual for its electric boilers.
Spare parts and service
Boiler spare parts
Spare parts for the ECOTHERM Electric Hot Water Boiler, sourced through ECOTHERM. Send us the boiler serial number for part numbers and lead times.
Ask about spare partsCommissioning and boiler service
Our technicians commission new boilers and service existing ones, including burners, controls, and water treatment checks.
Book a boiler serviceECOTHERM Electric Hot Water Boiler FAQs
What output does the ECOTHERM electric hot water boiler cover?
Fourteen standard models run from 72 kW to 2,016 kW. Two or three boilers can be joined in a cascade for 3 to 6 MW, and ECOTHERM builds larger units to order up to 30 MW.
When does an electric hot water boiler make sense?
When electricity is the only energy on site, when a gas supply or chimney is not practical, or when a site wants to use surplus solar or wind power as heat (power to heat).
How are the heating elements maintained?
Each element screws in and can be replaced on its own, so a failed element does not mean replacing the whole heater bank.
What pressure and temperature does it run at?
Standard operating pressures are 6, 10, or 16 bar(g), with water up to 110°C. Higher pressures and temperatures are available on request.
What approvals does a boiler need in Australia?
Many boilers are registrable plant under work health and safety law, which can mean design registration and plant registration with your state regulator, depending on the boiler's hazard level. Talk to us early and we will work through what your site needs. Call 1300 556 380.
Who supplies and services ECOTHERM boilers in Australia?
Hurll Nu-Way, based in Glen Waverley, Victoria, supplies ECOTHERM boilers and provides installation support, commissioning, servicing, and spare parts sourced through the manufacturer. Call 1300 556 380.
Page last updated October 2026.
Need a boiler sized for your site?
Tell us the heat or steam load, the energy you have on site, and the space, and our engineers will recommend the right boiler.
