Secomak 587/2 High Velocity Blower
A belt-driven high velocity blower giving up to 760 m³/h and 98 mbar on a 5.5 kW three phase motor. For drying, blow-off, and process air where pressure matters.
At a glance: The Secomak 587/2 is a belt-driven high velocity blower that delivers up to 760 m³/h and up to 98 mbar from a 5.5 kW three phase motor. It suits air knife drying, blow-off, cooling, and process air, and needs very little maintenance thanks to its sealed bearing assembly. Hurll Nu-Way supplies and services Secomak blowers in Australia.
High pressure air from a compact blower
The Secomak 587/2 is a high velocity centrifugal blower: low volume, high pressure air from a compact, belt-driven unit. It delivers up to 760 m³/h of air and up to 98 mbar of pressure from a 5.5 kW three phase motor. It gives the highest pressure in the 587 family.
The 587 is a 5.5 kW high velocity blower for larger air knife and process air duties. Choose the 587/2 for up to 760 m³/h and 98 mbar on a 5.5 kW motor. Within the 587 family, look at the 587/1 for more flow (up to 850 m³/h).
The fan chamber is machined from aluminium, and the drive belt and sealed bearing assembly keep maintenance to a minimum. It runs on a 50 Hz or 60 Hz supply. Secomak has built industrial fans and blowers in the UK since 1930, and every blower is hand built and tested before it leaves the factory.
Key advantages
- Belt drive with sealed bearing assembly
- Fan chamber machined from aluminium
- High pressure from a compact footprint
- Very low maintenance
- Runs on 50 Hz or 60 Hz
- Hand built and tested in the UK
Secomak 587/2 specifications
- Peak flow 760 m³/h
- Peak pressure 98 mbar
- Motor 5.5 kW
- Power supply 415 V three phase (rated 380 to 480 V), 50 or 60 Hz
- Run current 10.6 A
- Weight 84 kg
- Noise level 90 dB(A) at 1 m
- Drive Belt drive, sealed bearing assembly
Compare the 587 family
| Model | Peak flow (m³/h) | Peak pressure (mbar) | Motor (kW) |
|---|---|---|---|
| 587/1 | 850 | 58 | 5.5 |
| 587/2 | 760 | 98 | 5.5 |
Figures from Secomak. Peak flow and peak pressure are the two ends of each model's performance curve, not a single duty point.
Secomak 587/2 datasheets and brochures
Secomak's current datasheet for the 587/2, with the performance curve and dimensional drawing.
Secomak Model 587/2 1 document
Spare parts and service
Blower spare parts
Bearing assemblies, belts, impellers, and motors for the Secomak 587/2, sourced through Secomak. Send us the serial number for part numbers and lead times.
Ask about spare partsBlower overhaul and service
Our technicians overhaul and service industrial blowers on site or in our workshop, and commission new installations.
Book a blower overhaulSecomak 587/2 FAQs
What flow and pressure does the Secomak 587/2 give?
Up to 760 m³/h of air and up to 98 mbar of pressure. These are the two ends of its performance curve: peak pressure at low flow, and peak flow at lower pressure. The datasheet shows the full curve.
Should I choose the 587/2 or another 587 model?
Choose the 587/2 for up to 760 m³/h and 98 mbar on a 5.5 kW motor. Within the 587 family, look at the 587/1 for more flow (up to 850 m³/h). Tell us the flow and pressure your process needs and we will confirm the model.
What power supply does the 587/2 need?
A 415 V three phase supply (it is rated 380 to 480 V, 50 or 60 Hz), drawing 10.6 A.
How much maintenance does a belt-driven Secomak blower need?
Very little. The bearings are in a sealed assembly, so routine care is checking belt tension and wear. Our technicians can overhaul Secomak blowers when the bearings or belt need replacing.
Who supplies and services Secomak blowers in Australia?
Hurll Nu-Way, based in Glen Waverley, Victoria, supplies Secomak blowers and gas boosters, and overhauls and services blowers on site or in our workshop. Call 1300 556 380.
Page last updated October 2026.
Need a blower sized for your process?
Tell us the flow, the pressure, the air temperature, and your power supply, and our engineers will recommend the right blower.